空壓機選擇的基本準則有三條，可靠性、安全性與經濟性。
一、機器的使用環境和條件。在場地?zé)o供水，場地狹小的情況下，選擇立式空壓機;場地有長距離的變動(超過500米)，須考慮移動式空壓機;場地不能供電，則必須選擇風冷式。客戶們經常錯誤的認為水冷式比較好，其實在國內外小型空壓機中風冷式占百分之九十以上。原因是風冷式空壓機在設計上更加簡潔，無需水源。水冷式空壓機必須具備完善的供水系統，投資大;水冷卻器壽命較短;運行過程中大量浪費水資源;北方冬季易凍壞氣缸。
二、所需壓縮空氣的質量。一般的空壓機都含有一定的潤滑油，且含有水分，在禁油禁水的場合不僅要注意空壓機的選型，在必要的時候還要增加附屬裝置。此時可選擇無油空壓機。無油空壓機基本不含油，但潤滑不良，因此故障率高;此種空壓機因含有聚四氟乙烯，食品及制藥行業不能使用，無油空壓機只能做到不含油，但無法做到不含水。也可在空壓機后添加凈化裝置或干燥機，這種裝置能夠使空壓機不含油和水分，使含油水量在5ppm以下。
三、空壓機的排氣壓力及排氣量。常用的空壓機排氣壓力為0.7MPA，0.8MPA，目前社會上還有排氣壓力為0.5MPA的空壓機，輸氣距離過近。這種空壓機為一級壓縮，壓力比太大，易排氣溫度過高，造成氣缸積炭，導致事故的發生。大于0.8MPA的空壓機一般要特別制造，不可強行增壓?？諌簷C氣量的選擇要匹配所需的排氣量(并留有百分之十的余量)，空壓機檢查井鋼模具 隔離墩模具 隔離墩鋼模具 流水槽模具 U型槽模具 螺桿啟閉機 卷揚式啟閉機 銅雕佛像 最重要的參數之一就是排氣量。
四、運行的可靠性。空壓機運行時伴有升溫和壓力，運行的安全性是最重要的，現在國家對空壓機的生產進行規范化的“兩證”制度化管理，即空壓機生產許可證和壓力容器生產許可證。因此，在選擇空壓機時，一定要嚴格審查“兩證”，通常具備完善的產品質量保證系統。
Analytical summary of the basic criteria for air compressor selection,
there are three basic criteria for air compressor selection,
reliability, safety and economy. 1. The working environment and
conditions of the machine. In the case of no water supply and narrow
site, vertical air compressor should be chosen; if the site has
long-distance change (more than 500 meters), mobile air compressor
should be considered; if the site can not supply electricity, air-cooled
air compressor must be selected. Customers often mistakenly think that
water-cooled type is better, in fact, air-cooled type accounts for more
than 90% of small air compressors at home and abroad. The reason is that
the air-cooled air compressor is more concise in design and does not
need water source. Water-cooled air compressor must have perfect water
supply system with large investment, short life of water cooler, a large
amount of waste of water resources during operation, and easy to freeze
cylinders in winter in North China. 2. The quality of compressed air
required. General air compressors contain a certain amount of
lubricating oil and water. In the case of oil prohibition and water
prohibition, attention should be paid not only to the selection of air
compressors, but also to the addition of ancillary devices when
necessary. At this time, oil-free air compressor can be selected.
Oil-free air compressor basically does not contain oil, but the
lubrication is poor, so the failure rate is high; this kind of air
compressor contains PTFE, food and pharmaceutical industry can not use,
oil-free air compressor can only do without oil, but can not do without
water. It is also possible to add a purifying device or a dryer after
the air compressor, which can make the air compressor free of oil and
water, so that the oil and water content is less than 5 ppm. 3. Exhaust
Pressure and Exhaust Volume of Air Compressor. Commonly used air
compressor exhaust pressure is 0.7 MPA, 0.8 MPA. At present, there are
still air compressors with exhaust pressure of 0.5 MPA in society, and
the distance of gas transmission is too close. This kind of air
compressor is one-stage compression, the pressure ratio is too large,
and the exhaust temperature is too high, resulting in carbon deposition
in the cylinder, leading to accidents. Air compressors larger than
0.8MPA are usually specially manufactured and cannot be pressurized by
force. The selection of air compressor volume should match the required
exhaust volume (with a 10% margin). One of the most important parameters
of air compressor is the exhaust volume. 4. Reliability of operation.
Air compressor operation is accompanied by heating and pressure, the
safety of operation is the most important. Now the state carries out
standardized "two certificates" institutionalized
