正確安裝壓縮機才能保證壓縮機按設計參數工作， 如安裝不正確， 將導致壓縮機排氣溫度高、振動大、聲音異常等一系列問題。首先將空壓機安裝在牢固的地面上， 設備基礎采用C20混凝土現澆。在空壓機廠房每個空壓機進氣柵所對的墻壁上標高為016m處分別安裝兩個軸流風機， 進氣柵的空氣流速不超過015m / s, 且設計進氣軸流風機的通風量與壓縮機風扇的風量相吻合， 保證了通風系統的通暢。為確保冷卻風道中空氣的壓降不超過30Pa, 設計時要保證從壓縮機出口排風管道截面積是空壓機頂部截面積的2～3倍。且此通風管道沒有縮頸。對其它機型螺桿壓縮機， 如冷卻風道中空氣的壓降超橡膠托輥 槽型托輥 皮帶托輥 平行托輥 保定搬家 保定搬家電話 保定搬家公司 保定搬家 銅鼎 銅獅子 過30Pa, 應在冷卻風道的出口安裝通風風扇， 才能保證壓縮機出口溫度控制在正常范圍內。空壓機的通風系統在投運初期出現排氣溫度高達108℃的現象， 經查找原因分析， 是因?yàn)樵谖逶路菘諝庵械臉?shù)型槽模具 一次性止血帶 保定水處理設備 一次性止血帶 保定空壓機 北京真空泵毛比較多， 堵塞了板翅式換熱器， 影響了出口氣的換熱效果。為防止樹毛堵塞板翅式換熱器， 在兩個軸流風機的入口分別加裝60目的不銹鋼網， 效果十分明顯。另外，在以后的運行過程中， 做到定期吹掃板翅式換熱器， 以后再?zèng)]有出現排氣溫度高的現象。
The correct installation of the compressor can ensure that it operates according to the design parameters. If not installed correctly, it will lead to a series of problems such as high exhaust temperature, high vibration, and abnormal sound of the compressor. Firstly, install the air compressor on a solid ground, and the equipment foundation is cast-in-place with C20 concrete. Two axial flow fans are installed at an elevation of 016m on the wall opposite each air compressor intake grille in the air compressor plant. The air flow rate of the intake grille does not exceed 015m/s, and the designed ventilation volume of the intake axial flow fan matches the air volume of the compressor fan, ensuring the smoothness of the ventilation system. To ensure that the pressure drop of the air in the cooling air duct does not exceed 30Pa, the design should ensure that the cross-sectional area of the exhaust duct from the compressor outlet is 2-3 times that of the top cross-sectional area of the air compressor. And this ventilation duct has no necking. For other types of screw compressors, such as the air pressure drop in the cooling air duct exceeding that of rubber rollers, grooved rollers, belt rollers, parallel rollers, Baoding movers, Baoding movers, Baoding movers, Baoding movers, Baoding movers, and copper lions, which exceed 30Pa, a ventilation fan should be installed at the outlet of the cooling air duct to ensure that the compressor outlet temperature is controlled within the normal range. The ventilation system of the air compressor experienced a phenomenon of exhaust temperature as high as 108 ℃ in the early stage of operation. After investigation and analysis, it was found that there were many tree hairs in the air in May, which blocked the plate fin heat exchanger and affected the heat exchange effect of the outlet gas. To prevent tree hairs from blocking the plate fin heat exchanger, 60 mesh stainless steel mesh was installed at the inlet of the two axial flow fans, which has a very obvious effect. In addition, in the future operation process, the plate-fin heat exchanger should be regularly purged, and there should be no phenomenon of high exhaust temperature in the future.
